How to photograph an aurora
This is a brilliant article by Loic Le Guilly posted on https://digital-photography-school.com/how-i-captured-my-first-aurora-australis/
“My friend started shooting and the results on the camera screen were pretty exciting. The camera sensor and a long exposure reveal a lot more light and colour that can be seen by the naked eye. He kindly offered me to shoot a few frames. I decided to go for it with a 30 second exposure at 3200 iso, 16mm rectilinear lens wide open at f2.8. This can be too bright for really active auroras but I wanted to capture as much of the Milky Way as possible. The first shot I took is the one you see below (straight out of the camera). When I checked the image on the camera the green of the aurora looked very bright but I knew it wasn’t completely overexposed. But the upper red glow was recorded very nicely. Some low drifting clouds added a nice movement to the shot.
Post processing in Lightroom
I was very excited by the shot I got but I knew I could improve it in Lightroom (I had shot in raw format as I always do). This is a what I did :
- crop and straighten
- white balance – In my experience long exposures introduce a yellow tinge to night photographs. I took the white balance from daylight (5500K) to 3750K.
- exposure – I reduced the overall exposure by half a stop. I also applied another -1 stop to the green part of the aurora (with the adjustment brush).
- contrast – Long exposures at night tend to give flat images. I increased the overall contrast of the image (blacks to 19, contrast to 74, curve to medium contrast). I also pushed the local contrast (clarity to 100). That setting alone revealed the “curtain” of the aurora really well. Finally I increased the contrast further to the top third of the image to darken the sky.
And this is the final result.
And here is another image made from 2 shots stitched together in PTGUI. This one was 20 seconds at 3200 iso.
Not bad for a first night with an aurora.
How to know when an aurora might be coming ?
Personally I use the Facebook group Aurora Australis Tasmania. Its members are very knowledgeable and helpful. There is another Facebook group which is less Tasmania specific, Aurora Australis.
Final tips for photographing an aurora australis
- a clear night
- a spot looking south and ideally away from city lights (to avoid light pollution and flare)
- a tripod + camera + wide angle lens (ideally f2.8 or faster)
- use a remote trigger with mirror lock to reduce camera shake (if no remote than use timer on camera)
- ideally shoot in raw format for better quality
- noise reduction off (if shooting raw) to save time
- manual focus to infinity (test on a clear night before hand to avoid disappointment)
- iso 1600 to 3200 (or more if your camera can handle)
- exposure 10 to 30 seconds (longer exposures will start to show stars as trails rather than dots)
- these settings will depend on the brightness of the aurora so experiment, adjust and shoot lots of images !
Photographing an aurora is a truly exciting experience. I have read that 2013 should be a good year for auroras so keep an eye out and be ready !”
About the author
Loic Le Guilly is a photographer and web designer based in Hobart, Tasmania.
When not creating websites or shooting commercialy, he loves to wander in the bush to capture the natural beauty of Tasmania.
Some Older Comments
http://www.sws.bom.gov.au/Aurora/3/1
http://www.sws.bom.gov.au/Aurora/3/1
A.Horn Finland https://alexanderhorn.fi/2016/10/14/northern-lights-free-wallpapers/#lightbox[group-2251]/2/
www.hobartphotographertasmania.com.au/prints/
Thanks again
Loic
Just for many reading this, turn around and look north.
Anyways, I’m rambling on a bit here, congrats on the first shots – they’re definitely something to be proud of and will always be motivation to go out and shoot again! 🙂